Z-LinkCalc [March-2022] Features: Use multiple loss charts, radio frequency, frequency, radio power, power level and in some cases both with elevation and azimuth Two different sets of data tables are included Optionally include elevation/azimuth data in each of the charts Optionally input radio power and frequency to enable easy range to any one of the included charts Calculate range in meters or kilometers, if entered in feet or miles it will be converted automatically Download Z-LinkCalc You can download Z-LinkCalc completely free from HERE. To use the software, just copy and paste the following code into the HTML of your webpage: Please note: The file can be bigger than 16K so please only use the part of the file that you need. You can also download the zip file from HERE. Current version: 3.11.05 Z-LinkCalc User Guide: You can find a user guide for Z-LinkCalc by clicking HERE. Why do I need Z-LinkCalc? This question may seem silly but it's not. What if you flew with a quad and your receiver's sensitivity was too low. You would go for the range but you wouldn't be able to see the quad, wouldn't you? You would not know if your quad is flying over mountains or even the sky or close to another radio tower so you wouldn't be able to control your quad. You would end up flying way out of your quad and it could get damaged, right? There are many situations where knowing the range of your radio transmitter will be very helpful. Z-LinkCalc User Guide To use Z-LinkCalc you have to know a few things: What you are trying to do with Z-LinkCalc Most FPV controllers (or indeed any radio) use a specific frequency (RF channel). This means they will be using frequencies in the UHF frequency range (e.g. 1446.1MHz) or in the VHF frequency range (e.g. 108MHz). If your radio is based on a transmitter module (such as a.u.R.) then it will operate within a specific operating range (e.g. x25 is in the x5MHz range). If your radio is based on a Z-LinkCalc Patch With Serial Key 8e68912320 Z-LinkCalc Full Product Key (Final 2022) Connect to Arduino Open serial monitor (Tools > Serial Monitor) Calculate the range of the radio and write it in the serial monitor (if you have too). RX frequency TX frequency RC frequency (Output) RC frequency (Input) RC frequency (Hybrid) TX power (dBm) RF gain (omnidirectional) Radiation efficiency (omnidirectional) Bias-temperature coefficient of resistance (BtCoef. ~-10/C) IR loss (Bias-temperature coefficient of resistance) IR loss (Omnidirectional) IR gain (Omnidirectional) Input/Output impedance (Omnidirectional) Power (W) Receiver sensitivity Output power (dBm) I don't want to get that much information, and I didn't use any IDE, just downloaded and made it in QBasic. I added a button which says "calculate range", and when I press it, it runs the subroutine and gives me a result. I would like to have a table with all this info and keep track of changes. I tried doing so with a.txt file and I ended up with this: RC frequency (input) = 1.9554 RC frequency (hybrid) = 2.1176 RC frequency (output) = 2.0714 RX power (dBm) = -40 Radiation efficiency = 0.00039 IR loss = 0.02133 Input/output impedance = 8.0241 Power = 0.0286 Receiver sensitivity = -61.6874 TX frequency = 2.0299 RC frequency (hybrid) = 2.1286 I'm not sure if this is correct or not, I just tried to copy and paste the last line of the result table. I have an Arduino UNO, and all this code is stored inside an.exe file. A: Like i mentioned in my comment, I would store all the information in a database, and use a web service What's New in the? System Requirements For Z-LinkCalc: Game installation: - Download link - How to run game: (1) Set the render option to Low (2) Set the depth option to Hi (3) Set the Y render option to Off (4) Set the Z render option to Off (1) Set the render option to Low(2) Set the depth option to Hi(3) Set the Y render option to Off(4) Set the Z render option to Off You should know
Related links:
Comments